Featured: Maggy London Satin Stole
Lustrous satin fashion fabric shapes an elegant wrap designed with a pull-through slit opening for easy adjustability, like this one by Maggy London.
You will need:
- 2 yds. (1.8 m) of satin fashion fabric, 45″ wide
- Coordinating thread
- Small patch of fusible interfacing
- Fray Check ® fabric sealant
PATTERN
Make stole pattern approx. 16″ X 80″. Round the ends with a circular template (I used a large pie plate). Position slit opening 4″ from one end.
CUTTING
Cut 2X self
ASSEMBLY
Making a Bound “Buttonhole” Slit
TIP: To insure perfect results, make a trial buttonhole slit on the same number of fabric layers as your garment for practice.
Step 1: Mark slit position and length on WRONG (interfaced) side of one of the stole portions. Thread-trace a 4-inch slit, extending the thread tracing beyond end markings. The thread-traced markings should resemble a ladder.
Step 2: Cut a self fabric patch for the slit on straight grain, 2″ (5cm) wide and 5″ (13cm). Make a center line horizontally across the length of the patch. With RIGHT sides together, baste the center of the patch along ladder rungs with ends extending 1/2″ (1.3cm) beyond ladder sides.
Step 3: On WRONG side, mark lines 1/8″ (3mm) above and below buttonhole marking, using tailor’s chalk.
Step 4: Using a small machine-stitch, start sewing along one long side of the buttonhole, following pencil lines, being careful to end stitching exactly at thread-traced ends. Do not stitch across ends, back-stitch or pivot at corners. Bring thread ends to WRONG side and tie in a knot.
Step 5: Snip between the two stitching lines and clip diagonally to corners, as shown. Be careful not to clip through machine stitching. (TIP: Add a dot of seam sealant such as Fray Check® to corners, and allow to dry.)
Step 6: Pull patch through opening to WRONG side of front. This opening should form a perfect rectangle. Roll edges of opening between your fingers until each seam is at the edge of the opening. Press so that none of the patch shows on the OUTSIDE.
Step 7: To form “buttonhole” lips, fold each long side of the patch over the opening, so that the folds meet exactly at the center.
Step 8: On OUTSIDE, baste “buttonhole” lips together along fold lines and press in place. Basting should remain in place until stole is completed.
Step 9: To secure “buttonhole” lips and keep them from shifting, with front RIGHT side up, fold it back out of the way until you can sew the end of the patch and the triangle (formed by clipping corners in step 5) together. Using small machine stitches, stitch across the base of the triangle, catching patch. Trim end to 1/4″ (6mm). Repeat on other end.
Step 10: Stitch horizontal seam allowance of buttonhole and patch together, just inside the original stitching. Trim patch to 1/4″ (6mm). Repeat on other seam. Set aside.
Step 11: On second stole portion, repeat step 1.
Step 12: Cut a self fabric patch for the slit on bias grain, 5″ (13cm) wide and 5″ (13cm). Make a center line diagonally across the patch. With RIGHT sides together, baste the center of the patch along ladder rungs with ends extending beyond ladder sides.
Step 13: On WRONG side, mark lines 1/8″ (3mm) above and below buttonhole marking, using tailor’s chalk.
Step 14: Using a small machine-stitch, start sewing along one long side of the buttonhole, following chalk lines, being careful to end stitching exactly at thread-traced ends. Pivot at corners and complete the “rectangular” shape of the back opening.
Step 15: Snip between the two stitching lines and clip diagonally to corners, as shown in step 5. Be careful not to clip through machine stitching.
Step 16: Pull patch through opening to WRONG side of front. This opening should form a perfect rectangle. Roll edges of opening between your fingers until each seam is at the edge of the opening. Press so that none of the patch shows on the OUTSIDE.
Step 17: After the stole perimeter is completed, align the opening with the bound “buttonhole” slit and slipstitch rectangle opening to back of “buttonhole” lips.
Making The Stole
Step18: With RIGHT sides together, layer the 2 stole pieces and align the slit openings. Pin/baste the outer edges. Stitch around the perimeter, leaving 5″ opening along one long edge. Grade and trim seam allowances.
Step 19: Turn stole right side out. Slip stitch opening closed.
Step 20: Match and align bound “buttonhole” slit. Complete step 17.
Aucun commentaire:
Enregistrer un commentaire